Audi 100/A6
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
- 3.2. Diesel engines
+ 3.2.1.2. Technical characteristics
- 3.2.2. 5-cylinder engines
3.2.2.2. Technical characteristics
3.2.2.3. Sinkhronizatsionnye of a gazoraspredeleniye label
3.2.2.4. Compression check
3.2.2.5. Gas-distributing belt
3.2.2.6. Driving belt of the fuel pump
3.2.2.7. Natyazhitel of a gas-distributing belt and asterisk
3.2.2.8. Additional driving belt
3.2.2.9. Camshaft cover
3.2.2.10. Camshaft epiploons
3.2.2.11. Epiploons of a cranked shaft
3.2.2.12. Head of cylinders
3.2.2.13. Hydraulic pushers
3.2.2.14. Flywheel
3.2.2.15. Engine fastenings
3.2.2.16. Oil pallet
3.2.2.17. Oil pump and maslozaborny branch pipe
+ 3.3. Removal and partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice
|
| Engine code:
|
| 2370см3, direct injection, normal absorption, 64 kW |
AAS
|
| 2460см3, direct injection, turbonagnetatel, 85 kW |
ABP, AAT
|
| 2460см3, direct injection, turbonagnetatel, 103 kW |
AEL
|
| Diameter of the cylinder:
|
| AAS |
79,5 mm
|
| ABP, AAT, AEL |
81,0 mm
|
| Piston stroke:
|
| AAS |
95,5 mm
|
| ABP, AAT, AEL |
95,5 mm
|
| Extent of compression:
|
| AAS |
23,0:1
|
| ABP, AAT, AEL |
20,5:1
|
| Pressure of a compression:
|
| AAS |
26,0 bar
|
| ABP, AAT, AEL |
24,0 bar
|
| The maximum difference of pressure between cylinders |
5,0 bar
|
| Operating procedure of cylinders |
1-2-4-5-3
|
| N1 cylinder arrangement |
From a gas-distributing belt
|
| Greasing system:
|
| Type of the oil pump |
It is fixed in a forward part of the block of cylinders and receives a drive from a cranked shaft
|
| Nominal pressure of oil |
2,0 bar at least (2000 rpm, oil 80 temperature °)
|
Moments of an inhaling, N of m.
| The bolts, fixing the generator to an arm |
45
|
| Bolts of a natyazhitel of a driving belt |
20
|
| Bolts and nuts of a cover of a rod:
|
| – cтупень 1 |
30
|
| – cтупень 2 |
Tighten for 90 °
|
| The bolts, fixing the vacuum pump of brakes to a head of cylinders:
|
| – ABP, AAT, AEL |
10
|
| – AAS |
20
|
| Bolts of a cover of the bearing of a camshaft |
20
|
| Bolts of a cover of a camshaft |
10
|
| The bolts, fixing covers of forward and back bearings of a camshaft |
20
|
| Bolt of an asterisk of a camshaft:
|
| – ABP, AAT, AEL: |
| • cтупень 1 |
30
|
| • cтупень 2 |
Tighten for 90 °
|
| – AAS: |
| • bolt 8.8 |
85
|
| • bolt 10.9: |
| •• step 1 |
30
|
| •• step 2 |
Tighten for 90 °
|
| Ventilating channel of a case of the engine |
20
|
| Ventilating channel (ABP, AAT, AEL) |
10
|
| Bolt of a pulley of a cranked shaft:
|
| – ABP, AAT, AEL release to 11/94: |
| • step 1 |
160
|
| • step 2 |
Tighten for 180 °
|
| – ABP, AAT, AEL release after 11/94: |
| • step 1 |
220
|
| • step 2 |
Tighten for 270 °
|
| • ASS |
450
|
| Casing of a back epiploon of a cranked shaft:
|
| – М6 |
10
|
| – М8 |
20
|
| Oil jet of the cylinder |
10
|
| Bolts of a head of cylinders:
|
| – step 1 |
40
|
| – step 2 |
60
|
| – step 3 |
Tighten for 180 °
|
| – step 4 |
Warm up the engine
|
| – step 5 |
Tighten for 90 °
|
| – step 6 (only ABP) |
Tighten for 90 ° after 1000 km
|
| The bolts, fixing an exhaust pipe to a collector (AAS) |
40
|
| The bolts, fixing an exhaust pipe to a turbonagnetatel (to ABP, AAT, AEL) |
40
|
| Flywheel bolts:
|
| – step 1 |
30
|
| – step 2 |
Tighten for 90 °
|
| Bolts of a cross-piece of a forward suspension bracket:
|
| – step 1: |
| • AAS |
110
|
| • ABP, AAT, AEL |
100
|
| – step 2 |
Tighten for 90 °
|
| The bolts, fixing an arm of the fuel pump to the block of cylinders (AAS) |
50
|
| The bolts, fixing a cover of a driving belt of the fuel pump:
|
| – to a head of cylinders |
20
|
| – to the fuel pump |
10
|
| Bolt of an asterisk transferring a drive to the fuel pump:
|
| ABP, AAT, AEL |
100
|
| AAS |
160
|
| Bolt of an asterisk of the fuel pump |
50
|
| The bolts, fixing the fuel pump to an arm (AAS) |
25
|
| The bolts, fixing a plate of the sensor of the Hall to an inlet collector |
25
|
| The bolts, fixing the Hall sensor to a head of cylinders |
10
|
| Bolts of a cover of the radical bearing:
|
| – AAS |
65
|
| – ABP, AAT, AEL |
| • step 1 |
30
|
| • step 2 |
Tighten for 90 °
|
| Oil filter |
| Reduktsionny valve of the oil pump: |
| Cap without the temperature sensor |
40
|
| Cap with the temperature sensor |
30
|
| Bolts of the oil pump |
20
|
| The bolts, fixing a maslozaborny branch pipe to the pump and the block of cylinders |
10
|
| The bolts, fixing the power steering pump to an arm |
20
|
| Bolts of the oil pallet |
20
|
| Intermediate pulley of a gas-distributing belt |
10
|
| Bolts of an internal cover of a gas-distributing belt |
10
|
| Bolts of an external cover of a gas-distributing belt |
20
|
| Bolts of fastening of the cooling fan |
10
|
| Fan bolts |
20
|
|
|
